What're your thoughts and feelings about Installing A Bathtub?
Installing a tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to move out the old tub as well as set in the brand-new one. Make sure you have actually qualified yourself for the job and fit trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already purchased a new bathtub and also do not require to alter the setup of your previous water supply pipes.
Your tools as well as product list should make up the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Protect the faucet in position with the producer provided backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the called for position. The wood boards are helpful in equally spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub up until the spirit level checks out level.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water and inspect all joints and new pipework for leakages and tighten them if essential. Fill the tub and likewise examine the overflow outlet and also the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used a minimum of when as this will certainly settle it right into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very intrigued by Tools You Need to Install a New Bathtub and I am assuming you enjoyed reading the blog post. For those who enjoyed our post kindly make sure you remember to share it. Thanks a bunch for your time. Kindly check our blog back soon.
Call